DoseRoutine

Ipamorelin Dosage Calculator

Ipamorelin doses sit around 200–300 mcg, so how much bacteriostatic water you add decides whether your draw is a readable 10–30 units or an unmeasurable 4. Work it out below.

This is a unit converter. It converts an amount you already have into volume and syringe units. It does not tell you what to take, and it is educational only — not medical advice. Confirm every amount with your clinician and your product label.

Common setups

Vial size (mg)

Total compound in the vial.

BAC water added (mL)

Volume of bacteriostatic water you reconstitute with.

Target dose

Per-injection dose you want to draw.

Syringe type

U-100 = 100 units per mL (standard). U-40 = 40 units per mL.

Draw

10.0 units

on a U-100 insulin syringe (0.100 mL)

Concentration

2.00 mg/mL

Per dose

200 mcg

Doses / vial

~25

Ipamorelin concentration reference (mg/mL)

What each vial size becomes at common bacteriostatic water volumes.

Vial	+ 1 mL	+ 2 mL	+ 3 mL	+ 5 mL
2 mg	2.00 mg/mL	1.00 mg/mL	0.67 mg/mL	0.40 mg/mL
5 mg	5.00 mg/mL	2.50 mg/mL	1.67 mg/mL	1.00 mg/mL
10 mg	10.00 mg/mL	5.00 mg/mL	3.33 mg/mL	2.00 mg/mL

Ipamorelin dosing at a glance

Phase	Dose	Frequency	Notes
Common dose	200–300 mcg	1–3× daily	Roughly the saturation point for a GH pulse.
Timing	—	Fasted / before bed	Food and insulin blunt the pulse.
Paired with	100 mcg CJC-1295	Same injection	GHRH + GHRP synergy is the usual reason to stack.
Cycle	—	8–12 weeks	Then a break; long-term data is absent.

Reference ranges reported in the literature and in common practice — not a prescription, and not personalised advice.

What trips people up

5 mg + 5 mL = 1 mg/mL, so 200 mcg = 20 units — much easier to read than the 10 units you get at 2 mg/mL.
Ipamorelin is the selective GHRP: less cortisol and prolactin impact than GHRP-2 or GHRP-6, and far less hunger than hexarelin.
Going above the saturation dose does not increase the GH pulse — it just costs more.
It is on the WADA prohibited list at all times for tested athletes.

How the maths works

Concentration (mg/mL) = vial mg ÷ bacteriostatic water mL.
Volume per dose (mL) = dose mg ÷ concentration.
Syringe units = volume × 100 on a U-100 syringe, or × 40 on a U-40 syringe.
Doses per vial = vial mg ÷ dose mg. Water volume never changes this number.

Ipamorelin calculator FAQ

How many units is 200 mcg of ipamorelin?

At 2 mg/mL (5 mg + 2.5 mL) it is 10 units on a U-100 syringe. At 1 mg/mL (5 mg + 5 mL) it is 20 units — the more accurate option for a dose this small.

How much BAC water should I use for 5 mg of ipamorelin?

2.5 mL to 5 mL. More water means larger, more readable draws with no change to the drug itself. 5 mL is the better choice if you are dosing 200 mcg.

How many doses in a 5 mg ipamorelin vial?

Twenty-five doses at 200 mcg, or about sixteen at 300 mcg. Reconstitution volume does not change the count.

Is ipamorelin better alone or with CJC-1295?

The pair is standard because they act on different receptors — CJC-1295 raises the amplitude of your own GHRH signal while ipamorelin triggers the pulse. Alone, ipamorelin still works, just with a smaller effect.

Ipamorelin reference page Check interactions CJC-1295 + ipamorelin guide

Educational tool only — not medical advice. Verify every dose with your prescriber and follow sterile technique. See our medical disclaimer.

More free DoseRoutine calculators and dosing references.